1 1. INTRODUCTION This series is a compact and fully pure sinewave line interactive UPS, and it designs for critical application and environment, suc
3. SYSTEM DESCRIPTION Battery Level Indicator: There are four LED bar graphic to indicate the amount of battery capacity remaining. The hig
3. SYSTEM DESCRIPTION Back Panel - VI-750R / 1000R Rear panel description for LV and HV models table Function No
3. SYSTEM DESCRIPTION VI-1500R / 2000R 1. Host Rear Panel: The host rear panel pictures for HV and LV models are shown as below: Host
Rear panel description for LV and HV models table Function No. LV model (110/120/127Vac) HV model (220/230/240Vac)1 RS232 / Dry-Contact Communicatio
3. SYSTEM DESCRIPTION EBM Rear panel for LV model Rear panel description for LV and HV models table 13 Function No. LV model
3. SYSTEM DESCRIPTION VI-3000R Rear panel for HV model Rear panel for LV model 16 15
Rear panel description for LV and HV models table Function No. LV model (110/120/127Vac) HV model (220/230/240Vac) 1 Output Breaker 2 AC Output 3 AC
4. INSTALLATION 1. Inspecting the Equipment Inspect the UPS upon receipt. If the UPS has been damaged during shipment, keep the box and packing mat
4. INSTALLATION 7. Turn On/Off To turn on/off the UPS, you should press the on/off switch three seconds at least. 8. UPS Setup All models series a
4. INSTALLATION VI-1500R / 2000R Host and EBM integrate into three types of tower forms 16 (a) Towe
2. SAFETY INSTRUCTION – CAUTION IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS - This Manual Contains Important Instructions that should be
4. INSTALLATION VI-3000R Tower form setup 1. Slide down the UPS vertically and put two UPS stands at the end of the tower.
4. INSTALLATION 10. Rack-Mount Setup 750/1000/1500/2000VA(optional) and 3000VA can be installed in 19” racks. And the UPS and external battery encl
4. INSTALLATION 3. Insert UPS into the slide assemblies and lock it in the rack enclosure. 4. Add up the front panels for bo
4. INSTALLATION VI-1500R / 2000R (optional) HOST and EBM integrate into a rack form 1. Place the UPS on a flat and in a clean place th
4. INSTALLATION 4. Pull two covers toward the direction shown as below. 24 5. Align the mounting bracket with the screw holes on
4. INSTALLATION 7. Tighten all screws up to front panels and setup rack-mount for front side is completed 8. Align two small mountin
EBM and EBM integrate a rack form VI-3000R Install the 3000VA series into 19” rack as shown below. . 1. Turn on
4. INSTALLATION 11. Emergency Power Off(EPO) set up 1500/2000VA and 3000VA include EPO port that allows power to be shut down the protected equ
5. ADDITIONAL BATTERY INSTALLATION SETUP 1500/2000VA and 3000VA include external battery port that allow to provide additional battery runtime. 1
5. ADDITIONAL BATTERY INSTALLATION SETUP Additional battery connection in tower form VI-3000R There is one external battery port for the
3 6. When replacing the batteries, use the appropriate replacement battery kits, same number and type of battery are MUST. 7. Do not open or muti
6. BATTERY REPLACEMENT When the Bad Battery indicator flashes and there is a continuous sounding, the battery may need to be replaced. Plea
6. BATTERY REPLACEMENT Follow the steps and Charts below to replace batteries: VI-750R / 1000R 1. Unscrew and remove the front panel on both
6. BATTERY REPLACEMENT 4. Slide the new battery into UPS 5. Reconnect the battery cable and screw up the battery retaining battery bracket. 6.
6. BATTERY REPLACEMENT 4. Pull the battery out onto a flat area. 35 5. Slide the new battery into EBM. 6. Reconnect the battery c
6. BATTERY REPLACEMENT 3. Unscrew the battery bracket from the EBM 4. Remove the battery bracket from EBM by pulling on both ends.
35 7. Slide the new batteries into EBM. 8. Reconnect the battery cable and screw up the battery bracket. 9. Close and reinstall the front
8. TROUBLE SHOOTING Audible Alarm Trouble Shooting: Problem Cause Solution Sounding every 4 seconds The UPS is on battery Check the input volt
Trouble Shooting Guide (Continue) Problem Cause Solution . Battery may not able to hold a full charge due to age.1. Recharge the battery at least 8
9. SPECIFICATION MODEL VI-750R/1000R VI-1500R/2000R VI-3000R CAPACITY Watt 750VA / 500W 1000VA / 700W 1500VA/1050W 2000VA/1340W 3000VA/ 2100W Vol
37 MODEL VI-750R/1000R VI-1500R/2000R VI-3000R AC Mode Line LED lighting Backup Mode Battery LED flashing every 4 seconds Site Fault Site faul
4 2. SAFETY INSTRUCTION – CAUTION 10. This UPS contains high voltages which may cause the risk of electric shock. Do not remove cover. There are
10. SOFTWARE INSTALLATION After the UPS has been installed, you must install the software (Smart Power) that came packaged with your UPS. Smar
2. SAFETY INSTRUCTION – CAUTION 2.1 Description of Commonly Used Symbols Symbol & DescriptionSymbol DescriptionAlert you to pay sp
3. SYSTEM DESCRIPTION Front Panel — No. Function Description 1 Switch ON/OFF 2 Switch Self-Test/ Alarm Silence 3 Switch Config 4 Switc
3. SYSTEM DESCRIPTION 1. Power Switch: - To turn on the UPS, press the button more than three seconds - To turn off the UPS, press and hold
3. SYSTEM DESCRIPTION 5. Input Type (Operating Mode) LED: Normal mode: The Yellow LED indicator will illuminate during normal mode, the
3. SYSTEM DESCRIPTION 10. PCB FAIL LED(or SITE FAULT LED): PCB FAIL LED: the LED indicator will light on when the power module of UPS fails.
Commentaires sur ces manuels