Powerwalker VFI 20000TP 3_3 BE Manuel d'utilisateur

PowerWalker VFI 3/3 SeriesVFI 20000TP 3/3 BE/BI380/400/415V 50/60Hz(3-phase input/output)User Guide

52.2 Basic system conguration2.3 Panel gure

6 EN 2.4 Exterior view①AC: This light and inverter light will turn "green" when UPS is powered by Rectier Input;②Inverter: This light

7CHGR FAN Front view(door open)Battery trays

8 EN 3 Technical data3.1 Standards Product IEC62040-3:1999 and EN62040-3:2001 UPS

93.5 AC input3.4 Characteristics VFI 20000TP 3/3 BE/BI

10 EN 3.7 AC output3.8 Battery and ChargerInternal battery package Panasonic LC-RW1245W CSB HR1234WF2Dimensions

114 Mechanical installation4.1 Delivery checkThe UPS and accessories are delivered on a specically designed pallet that is easy to move

12 EN Check the information on the type designation label of the equipment to verify that the unit is of the correct type. The type designation

13Preparation for installation.1. Avoid extremes of ambient temperature; excessive dust, moisture or vibration; ammable gases; and corrosive or explo

14 EN Caution!UPS cabinet(s) can fall over if the installation brake pads are not used. Both rear and front pads must be used to secure the UPS

15The normal positions of the MBS switches.The switching sequence for circuit breaker from normal position to maintenance position:

16 EN The maintenance positions of the MBS switches2.Use LCD to turn the UPS from normal mode to bypass mode:Switch-off action (press ESC to exi

171)Switch-off picture 2)If it is in single machine mode, the

18 EN 7.UPS is now in the maintenance bypass mode, see below (Note: the Serv disconnect i.e. battery fuse must be turned off):Transfer UPS from

19Then the UPS turn to bypass mode.4.Turn ON the Rectier Input switch and battery fuse.5.Use LCD to turn the UPS from bypass mode to normal mode:Swit

20 EN 6.UPS is now in the normal mode,see below:7.Remount the locking plate of maintenance switch to the position to prevent the use of it.

215 Electrical installation5.1 Electrical Preparations The UPS unit has the following power connections:Three-phase (L1, L2, L3), Neutral (N) and Prot

22 EN 1.If UPS rectier input and bypass input are supplied from two mains:Connect the mains 1 supply cables to the UPS rectier input terminals

23Terminal block diagramWarning!High touch current earth connection essential before connecting supply.2.If UPS rectier input and bypass inp

24 EN Routing of communication cables or data lines should be kept separate from the UPS input, output, and external battery cables.The conducto

EN ©2013 BlueWalker GmbH All Rights ReservedThe contents of this manual are the copyright of the publisher and may not be reproduced (even extr

25Use cable cross section and protective device specication Model

26 EN Warning!ENSURE THAT THE UNINTERRUPTIBLE POWER SYSTEM IS ISOLATED BE-FORE WORKING ON THIS CIRCUIT.5.4 Internal Battery Installat

274. Connect the cables to each shelf respectively (see Fig. 2).Remark: make sure the cables between the shelves are disconnected and the following

28 EN Fig. 3Table1: Battery cable list Label B1 B2 B3 B4 B5 No label B8 B9 B10 B11 B12 B13 B14 B15 B16

29Notice!The most common battery type used in UPS installations is the valve regulated bat-tery. Valve regulated cells are not sealed. The amount of g

30 EN 5.6 Connections between battery cabinet and UPSMake sure the Protective Earthing (PE) connected rst.External Battery Cabinet ConnectionsN

31Exchanging batteriesWarning!If a battery cabinet has been disconnected and is to be reconnected, the battery isola-tor may only be reconnected after

32 EN 6 Software and connectivityThe Series provide Intelligent Slot, Expanded Slot, PARALLEL, AS400, EPO, RS485 and RS232 as well as SERVICE Su

33RS232 portRS485 port

34 EN AS400 portNote!The UPS have to be manually reset if remote shutdown occurs.

4.1 Delivery check………………………………………………………………………4.2 Unpacking and visual inspection………………………………………………4.3 Planning before installation……………………………………………………

357 User operations7.1 Single machine operation Warning!High touch current earth connection essential before connecting supply.The only user operation

36 EN 3)Press ESC to access or automatically within 1min with no button being pressed4)Press▼to obtain the below informa-tionRemark: the followi

375)Press▼again to obtain the below 6)Press▼again to obtain the belowinformation

38 EN 1)Switch-on picture 2)Press ENTER4. Start-up action (press ESC to exit the above picture)N

393)Select “Yes, Conrm” to switch on 4)Normal Switch-onthe machine 5)Battery power supply (switch off lin

40 EN 3)If it is in parallel machine mode, the 4)Press ENTERfollowing will appear

415)Select “Yes, Conrm” to switch off 6)Normal Switch-offthe machine Note!If you intend to switch off only

42 EN 3)Enter respective password 4)Select action item8. The Series is capable of DC start-up without AC input,

439. Procedures of DC switch-on: Activate DC switch-on function set under UPS bypass mode Make sure that “+”, “-” and “N” wires of batteries are p

44 EN Parallel machine wire connection drawing(one battery supply)Parallel machine wire connection drawing(separate battery supply)

EN Recycling the used UPS or battery………………………………………………Maintenance……………………………………………………………………………Parallel systems…………….…………………………………………………………8.9.1

45Single machine wire connection drawing

46 EN PowerWalker VFI 20000TP 3/3 requires minimum maintenance.1. If battery is switched off, loaded equipments will not be covered for power-of

47Remark:A. Prior to battery replacement, switch off UPS and remove it from AC and battery, take off internal battery fuse.B. Take off metallic articl

48 EN 8.2 Regular service/intervalsThe UPS requires very little maintenance if installed in an appropriate environment. In order to ensure maxim

499 Parallel systemsParallel is only connected to identical ports for the UPS of same models and kVA rating.1) Follow installation instructions for ge

50 EN Note!Parallel signal cable should be connected as a loop.

5110 Recycling the used UPS or batteryBefore scrapping UPS or its battery cabinet, the battery bank must be removed. Local re-quirements must be follo

52 EN 11 Display reference Table

5353Should any display or warning message excluded in the above table be found,please con-tact distributor or call PowerWalker Hot line for advice.● I

11 Safety instructionsWarning!Operations inside the UPS must be performed by a service engineer from the manufac-turer or from an agent authorised by

614-01718-00

2 EN 1.3 CE markingThe product has the CE marking in compliance with the following European directives:LVD Directive (Safety)

31.5 Environment The UPS must be installed according to the recommendations in this manual.Under no cir-cumstances the UPS should be installed in an a

4 EN 2 Introduction2.1 System descriptionPowerWalker VFI 3/3 Series products are high-efficiency and high-performance, double conversion, pure-o